<-=- Club Bevel Heaven -=->

where can I get pads for my rebuilt caliper
the centerline distance for the cotter pins is 45 MM
does anyone know what type of pad will fit this dimention,
the ones I want to replase have had the holes elongated to line up with
the cotter pins.

I removed the gear selection housing, I had had it apart when I split the
engine case, springs are good and stiff and everything looked in order.
I remounted it and adjusted the screw clockwise 1/2 turn,you
can see the
shift lever moving as you do this. Test drive time, the down shifting into ...

I AM HAVING TROUBLE FROM TIME TO TIME DOWN SHIFTING,
SAY IN THIRD OR FOURTH AND NOT BEING ABLE GET INTO FIRST
AT THE TRAFFIC LIGHT, HAVING TO START OFF IN SECOND AND THEN BEING SBLE TO GET BACK INTO FIRST ???
ANY INFO ON ADJUSTING THE SCREW NEXT TO THE SHIFTER

I have mounted 12volt PVL coils on my GT and I am about to install
a new Dyna S ignition, I fried the leads on my old Dyna at the module
plate.
Any one had any kind of probs with this set up ??
the coils are oil filled and rated at 3.8 ohms primary and 5.5k secondary
resistance.
any need for a ...

Cafe
I will give them a call, I had all the chrome on the duck redone a Astro
in Van Nuys and they did a great job, asked them yesterday about doing
plastic they gave me the name of a place that can do it but they have a
Minimun fee of 750.00 -------ain't happening

Macdesmo
I ordered my new side ...

does anyone one know of a shop that will rechrome the "plastic" gas tank
badges from a 750 GT. The copper is showing through on one of mine Or anyone know where I can get a least one
new or a really good used one.
thanks
Gerard

flywheel nut, clutch drum nut 36 ftlbs ??? does that sound right ??
altinator nut 86 ftlbs and its a lot smaler than the flywheel nut ???
chain sprocket at 57 ftlbs??

everybody O.K. with these numbers, there from Falloon`s book
and I really do not have anything else to go on.
let me know ASAP ...

anybody familiar with a oil galley monification to supply more constant
oil delivery onto the gear stacks ???
what would you need to do it for ??? hard racing ???
Just wondering, someone mentioned it to me but they were not aware
of the process or reason ???

steve
I found the part I need in the gasket kit I received today.
I removed the threaded pin from the case bottom and fit the rubber
piece in place, the new sump screen threaded in and fit into the rubber
thing perfectly !!
Looking in through the r/h plug you can see how the screen and that rubber ...

the rod I used was 4043. I had used this rod in years past to weld
up the intake ports on vw cyl heads, most castings have a higher
silicone content than sheet or extruded parts and this rod has been used on castings for some time. start to finish from heating to finish machine
work was about 3 ...

I split the cases,soaked em in carb cleaner then clean solvent and finaly
used aluma clean around the plug hole.
I pre heated the case and welded up the ID of the hole--4043 no prod !!
13/16 end mill and 22x1.5 tap on mill, done deal. Just got the new
sump screen from Steve and now I am looking for ...

I contacted timeserts and the "oil pan kit" is 450.00 with 5 10 mm
inserts, as I am splitting the case anyway I think I will ck out the possibilities of welding in a plug and drilling and tapping to fit the new sumpscreen filter
I can weld it myself and get in on a mill at work to d&t.
after ...

the 22x1.50 mm threads where the sump screen fits into my case
are "GONE" previous owners epoxied the plug in place. I cannot get a Helicoil to repair the hole without spending about 6-800 bucks to get
Helicoil to make a miniumn of 100 pieces.
any body got a fix for this "nightmare"

Gerard

has anyone one done any welding on 750 GT cyl fins ??
I have a broken one and was wondering what kind of rod would be OK
for the cast aluminum fins
I am thinking they are probably a 356 alloy which is easy to weld but
just thought I would ask before I start
I want to do the welding before I have ...

Achim

My 750Gt is Early 1974 and has the Brembo master and the rectangular
splitter> If you have a pict of the break lines attached it would be helpfull.
I have already rebuilt the Brembo master and the Scarab caliper

thank`s
Gerard